Note: Hover your mouse over the “My GTI” link above to reveal a drop-down menu which lists write-ups for various changes to the car.
Quick Links for mobile users: Mechanical – Electronics – Accessories – Trailers/Cargo – Index of Parts/Equipment
I knew I was testing the limits of my stock clutch when I added 81 hp and 111 lb-ft with APR Stage 1. The car drove great and the clutch held the extra power for over 16,000 miles (for a total of 34,000 miles). However, turbocharged cars LOVE cooler temperatures due to an improved ability to make horsepower and avoid heat soak. So it was little surprise when my clutch began to slip as temperatures dropped in October. I probably could have put off a clutch upgrade, but driving the original clutch on our upcoming road trip over the mountains was out of the question, especially since I may take the trailer. I had planned to buy a Southbend Stage 2 Endurance clutch, but then I changed my mind…
I have a Southbend clutch on my Mk3; the little diesel sounds more like a Peterbuilt. I knew that converting to a single-mass flywheel would increase flywheel noise in my GTI, although probably not to the extent it did in my TDI. I wanted to continue my trend of hiding mods and didn’t want extra clatter drawing attention. So I chose an RSR clutch kit with Sachs flywheel by HS Tuning. It uses a factory-like dual-mass flywheel and is reported to be an upgrade to the clutch found in Audi’s 400-hp TT-RS. The clutch was advertised to hold 480 lb-ft when I bought it, but has since been updated as being suitable to hold 380 lb-ft in a Mk7. I’d buy their RSR Hybrid Clutch Kit if I was shopping today.
I had Euro Pros install the clutch. They are in Yorktown, VA, specialize in VW/Audi repair and service, and are the APR dealer that upgraded my ECU. They had not installed an RSR clutch kit before, but said everything was a breeze. Both the technician who did the work and the shop owner said the clutch feels great and has good pedal-feel (more on that later). They also gave the car a thorough inspection to see if anything needed attention. Everything was good with one exception.
They found one small problem in the form of an unexplained pocket of fluid in a cranny below the bell housing. The bell housing is completely dry, there’s no sign of leaking from the transmission case, and there’s no obvious paths that would have allowed the fluid be become trapped there. The VAQ differential may have a leak. The hardware is tightly packed, so finding the exact source of the leak is a challenge. I cleaned the transmission and watched the area for 100 miles, which wasn’t enough time to duplicate a tiny leak. I will check again in another 500 miles. Has anyone else had a leak here? I’ve shared more photos below. Have a look and feel free to tell me what you think.
Initial impressions: “Damn, it’s STIFF!” The factory clutch is so smooth and effortless that it probably has made me soft. 😉 The RSR clutch also engages closer to the floor than stock, but it didn’t take long to get used to it. It feels good and “correct”after a week, but it does not meet the advertised claim of “no noticeable increase in pedal effort,” NOT EVEN CLOSE, due to how soft the stock clutch works. “The laggy feeling clutch engagement, commonly blamed on the clutch hydraulic system, is completely eliminated, resulting in a fast and positive clutch engagement with no delay” is certainly a true statement! I had Euro Pros remove the restrictor from the hydraulic line, so the clutch is very snappy! It also exhibits stock levels of noise, as advertised. I tested noise levels by listening to the car in a drive-thru lane with the windows down. “Yep, it still sounds like a sewing machine.” I encourage younger readers to Google “sewing machine” if the term is confusing. 😉
I’m completely accustomed to the extra pedal effort; it inspires some confidence that it’ll hold the increased torque. I’m very pleased and will continue to be so long as the clutch lasts a long time. My only other niggle is a tiny, tiny bit of chatter felt through the chassis as the clutch engages from a stop. Euro Pros told me that it may or may not go away, but it was nothing to worry about. Most of the time, I just “drove through it” and didn’t even think about it. A week later, I’m pleased to report that the chatter is gone without a trace. I guess the flywheel just needed break-in time and to transfer friction material between the parts.
By the way, I allowed the clutch to “break-in” by driving moderately along stop-and-go routes for about 200 miles over three days. I did a glorious sprint the following morning. Later, I drove some coworkers to lunch. Between the four of us, there was probably 900-lbs of meat in the car, plus the 50-lb box with stock clutch was still in the trunk. I needed to make a left turn and saw the protected light turn green in the distance. Not wanting to miss it, I stabbed the accelerator in 2nd gear, just enough to chirp the tires, and blasted to the light. The team was impressed. The following morning, I gave a friend his first ride in a GTI. He loved it, especially since we didn’t wind up in jail. 😀 This car is a keeper!
The clutch upgrade happened earlier than expected. I’m not disappointed because I drove with the extra power on the stock clutch for over 15,000 miles, to include plenty of towing, which is pretty abusive to clutches. The timing of the costly upgrade sort of stinks since it was just before the holidays and a road trip. But now the foundation is in place for APR STAGE 2! Perhaps I’ll make that purchase as a birthday gift in February, along with some high-performance tires. The car should be a beast with the extra grip and Stage 2! 🙂 Speaking of birthdays, I just realized the car is nearly one year old! Do cars like cake? I know I do! 😉